After a few attempts, my Acer SW3-016 still refuses to find a bootable device, why is this the case?

1235

Answers

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    Here, I took a pic
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    OK. You now have 2 delete partition operations that are pending and thus not yet complete.  So now you must apply these changes from an option in one of the dropdown tabs, probably Gparted on your version.

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    Done, what now
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    (1) Shut the machine off.
    (2) Then insert your favorite 32-bit Linux distro installation stick.
    (3) Then turn the machine on and immediately start tapping the F12 key to boot from the stick.
    (4) Try to install the iso on the unallocated emmc chip

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    Alright then
  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    It didn’t work. At this point I might go back to windows again
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    edited August 2021
    What happens? What distro are you using? Installation stick must be GPT scheme. BIOS must remain in UEFI mode.

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    Ah I forgot to format it correctly 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    (1) What distro iso are you trying to use?
    (2) Are you preparing the iso with Rufus?

    Perhaps posting a screenshot of the Rufus preparation page would help to make sure all the options are properly set.

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    I used Rufus + I’m attempting to install linux lite, which I just realised isn’t 32bit :tired_face:
  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    I chose ISO Mode + GPT and the UEFI Option thing. + I also wiped the disk via GParted too
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Please post a screenshot of the Rufus setup with the 32-bit iso. If it fails, I suggest that you try to install 32-bit LinuxMint Cinnamon 19.3 iso since it has one of the better installers.

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    Alright I’ll try that 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Please post a screenshot of Rufus as you set up the iso.

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    Ok. I'll do it asap
  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer



    With the ISO you suggested I cannot select the GPT Partioning method, but with the Linux Lite 64bit I could
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Try changing the target system to UEFI only (NOT BIOS NOR UEFI CSM). 

    Jack E/NJ

  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    No difference, I'm beginning to really think a new laptop should become more of a priority.
  • Jeff7899
    Jeff7899 Member Posts: 80

    Tinkerer

    I used your suggestions, and made a bootable USB out of it, installation went fine but didn't end too well as the no bootable device error still cropped up
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    Partition Scheme should be GPT for UEFI boot, not MBR.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.