Iconia w700 BIOS shows hard drive but I get the "no bootable device error"

epc7405
epc7405 Member Posts: 8 New User

My 2 year old Iconia W700 will not boot. Error message is "no bootable device". The BIOS lists HDDO model Name: SandForce(200026BB) HDDO serial number:1

 

I have tried reseting the BIOS to factory default but thet doesnt work either.

 

Tried to boot from CD but get an error there too "security will not allow boot"

 

Please advise.

 

 

Thanks

 

Ed C.

Answers

  • Sharanji
    Sharanji ACE Posts: 4,328 Pathfinder
    Please try the below mentioned steps :
     
    To enter BIOS, power the system down completely.
    Press and hold the Windows button and power button until the Acer logo appears on-screen and then release the buttons.
    If you tablet is shipped wiht windows 8, you may disable secure boot.
    Completely shut down your computer. Enter the BIOS, Tap Security.
    Under Set Supervisor Password, tap Enter.
    Create a password and press Enter. Retype the password to confirm and press Enter again.
    Tap on the Boot tab. Below Secure Boot, change the setting from Enabled to Disabled.
    Save your settings by selecting Exit and tapping on Exit Saving Changes.
     
    Use the following steps to restore your Iconia W700 to factory default settings:
    Power the system off completely. Connect an external DVD optical drive.
    Enter the BIOS.From the BIOS, tap Boot. Locate and move USB CDROM: to the top of the boot priority list.
    Insert the Iconia W700 System DVD.Tap on Exit and then select Exit Saving Changes.
    The tablet will boot from the system DVD.Follow the on-screen instructions.
     

    Do get back to us and let us know the status of the issue by your next post or in case you need further assistance. We, at Acer strive towards excellence.

     

    Click the Kudos kudos-thumbs-up.png to say “Thanks” for helping! select "Accept Solution" if your issue is resovled.

  • billsey
    billsey ACE Posts: 34,276 Trailblazer

    Table corruption may cause the error message, No bootable device -- Please restart system. This may appear on notebooks with solid state drives (SSD) after an unplanned shutdown.

    Resolution

    This can be corrected using the following steps:

    1. Power on the computer and press F2 to enter the BIOS.
    2. Leave the system idle in the BIOS for 10 minutes.
    3. After 10 minutes, press F10 and select Yes to save and exit.

      Precaution Do NOT press the power button to exit the CMOS.

    Once the tables are synchronized, the computer should boot properly.

     

    Let us know if that works, there are other things that can corrupt a Windows boot...

    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • epc7405
    epc7405 Member Posts: 8 New User

    that did not work...

  • epc7405
    epc7405 Member Posts: 8 New User

    thanks...i ordered new recovery disks (cant find the original) and will let you know the result

  • epc7405
    epc7405 Member Posts: 8 New User

    I am using the Acer USB System Recovery Drive but the install hangs. cmd.exe executes but hangs at "Disk 0 is now the selected disk"

  • Waseem13962
    Waseem13962 Member Posts: 3 New User

    I also have the same problem of to completely restore Iconia W700 to factory defaults. I followed the steps told by you. All Went well as per your guidance. But once reaches Recovery Management window, every time it asks to cahange DVD mode from UEFI to Legacy or if it is changed to legacy it asks to change in UEFI.

  • Waseem13962
    Waseem13962 Member Posts: 3 New User

    I also have the same problem of to completely restore Iconia W700 to factory defaults. I followed the steps told by sharanji and you. All Went well as per your guidance. But once reaches Recovery Management window, every time it asks to cahange DVD mode from UEFI to Legacy or if it is changed to legacy it asks to change in UEFI.

  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer

    You need to delete partitions from HDD/SSD or the eRecovery will start this "dance" between UEFI and Legacy.

    try to create a bootable USB flash media with partition wizard:

    http://www.partitionwizard.com/partition-wizard-bootable-cd.html

     

    then delete all partitions:

    http://www.partitionwizard.com/help/delete-partition.html#howto

    I'm not an Acer employee.
  • Waseem13962
    Waseem13962 Member Posts: 3 New User

    The solution 'partitionwizard.com' you advised to delete partition did not work. I used http://gparted.org/download.php instead.

     

    Rest it went fine. Thanks BRAVO.

  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer

    good to hear it. Smiley Happy

    I'm not an Acer employee.