AN515/55 Nitro

System
System Member Posts: 4,562 Seasoned Practitioner WiFi Icon
This discussion was created from comments split from: Ram upgrade - AN515/55 Nitro.

Answers

  • gigs56din
    gigs56din Member Posts: 5

    Tinkerer

    Hi Everyone, i hope someone can enlighten me. I just bought this new laptop and my ram installed is 8gb w 2933mhz. I bought the same speed in amazon hyperX 8gb 2933mhz. But when I installed the new ram, the performance memory was changed to 2400mhz speed. Should I remove the one that I installed? Because it seems the ram speed that I bought is not the same to the one in my laptop. Please help. Thanks in advance 
  • gigs56din
    gigs56din Member Posts: 5

    Tinkerer


    Before I install the one I bought in amazon.



    After I install the one I bought in amazon. Ram speed was changed to 2400mhz
  • Spartan
    Spartan Member Posts: 2 New User
    I am planning to buy nitro 5 i5 10th gen ,8gb ram, 1tb hdd + 256 ssd, gtx 1650 ti ,...AN515-55.. What is the ram frequency ? I want to buy 8gb extra ram , so please tell the frequency of ram given in the laptop. Amazon and flipkart both dont have any detaila about it
  • robgc
    robgc Member Posts: 5

    Tinkerer

    When you buy RAM you have to be very careful to check the module timing. Especially the CAS latency timing. That hyperX RAM is likely slower CAS timings and would requires overclocking as CL is lower but the Nitro can’t be overclocked. I’m guessing your CL is at 17?

    I ran in to this issue as well when looking to buy RAM, many gaming RAM list 3200 Mhz but are lower base timings such as CL19 which is like running a 2666 Mhz module. 

    This is what I bought:

    Crucial 16GB DDR4 3200 MT/s (PC4-25600) SODIMM 260-Pin Memory - CT16G4SFRA32A

    This will also work: CT16G4SFD832A

    Both are CL22 modules. 

    My original RAM that came installed was 8ATF1G64HZ-3G2J1 from Micron and the Crucial also uses Micron chipsets so it is the best bet for adding modules in my opinion. 

    Yes, it may not be recommended to install different sized modules by RAM sellers but in reality this motherboard will adjust as long as the modules support the exact same timing specs for all 4 timings. I am now running 24GB in my machine. 8GB in dual channel and remaining 16GB in single channel with no issues all at 2933Mhz. 

    The final result because of the cpu clock speed is they run slightly slower at 2933Mhz with memory running at CL 21 with timings of 
    21-21-21-47 rather than at full speed CAS CL22 3200Mhz at 22-22-22-52 the module can handle. 

    To truly know what your memory modules are doing use cpu-z or HWinfo and look at the four number timings: 21-21-21-47 is for 2933Mhz. As this cpu/motherboard can’t do 22-22-22-52 it isn’t using the full memory speed ability so maybe running slower memory modules you won’t notice too much difference between say 2666 CL19 and 3200 CL22. I wanted the best memory in case I upgrade and might move it to a newer laptop at a later date. 



  • robgc
    robgc Member Posts: 5

    Tinkerer

    Spartan said:
    I am planning to buy nitro 5 i5 10th gen ,8gb ram, 1tb hdd + 256 ssd, gtx 1650 ti ,...AN515-55.. What is the ram frequency ? I want to buy 8gb extra ram , so please tell the frequency of ram given in the laptop. Amazon and flipkart both dont have any detaila about it
    This is what came in mine:

    [General Module Information]
    Module Number:2
    Module Size:8 GBytes
    Memory Type:DDR4 SDRAM
    Module Type:SO-DIMM
    Memory Speed:1600.0 MHz (DDR4-3200 / PC4-25600)
    Module Manufacturer:Micron Tech.
    Module Part Number:8ATF1G64HZ-3G2J1
    Module Revision:3.1
    Module Serial Number:[Hidden]
    Module Manufacturing Date:Year: 2019, Week: 43
    Module Manufacturing Location:5
    SDRAM Manufacturer:Micron Tech.
    DRAM Steppping:4.A
    Error Check/Correction:None
     
    [Module Characteristics]
    Row Address Bits:16
    Column Address Bits:10
    Module Density:8192 Mb
    Number Of Ranks:1
    Device Width:8 bits
    Bus Width:64 bits
    Die Count:1
    Module Nominal Voltage (VDD):1.2 V
    Minimum SDRAM Cycle Time (tCKAVGmin):0.62500 ns
    Maximum SDRAM Cycle Time (tCKAVGmax):1.60000 ns
    CAS# Latencies Supported:10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 26, 28
    Minimum CAS# Latency Time (tAAmin):13.750 ns
    Minimum RAS# to CAS# Delay (tRCDmin):13.750 ns
    Minimum Row Precharge Time (tRPmin):13.750 ns
    Minimum Active to Precharge Time (tRASmin):32.000 ns
     
    Supported Module Timing at 1600.0 MHz:22-22-22-52
    Supported Module Timing at 1466.7 MHz:21-21-21-47
    Supported Module Timing at 1333.3 MHz:19-19-19-43
    Supported Module Timing at 1200.0 MHz:17-17-17-39
    Supported Module Timing at 1066.7 MHz:15-15-15-35
    Supported Module Timing at 933.3 MHz:13-13-13-30
    Supported Module Timing at 800.0 MHz:11-11-11-26
    Supported Module Timing at 666.7 MHz:10-10-10-22
     
    Minimum Active to Active/Refresh Time (tRCmin):45.750 ns
    Minimum Refresh Recovery Time Delay (tRFC1min):350.000 ns
    Minimum Refresh Recovery Time Delay (tRFC2min):260.000 ns
    Minimum Refresh Recovery Time Delay (tRFC4min):160.000 ns
    Minimum Four Activate Window Delay Time (tFAWmin):21.000 ns
    Minimum Active to Active Delay Time - Different Bank Group (tRRD_Smin):2.500 ns
    Minimum Active to Active Delay Time - Same Bank Group (tRRD_Lmin):4.900 ns
    Minimum CAS to CAS Delay Time - Same Bank Group (tCCD_Lmin):5.000 ns
     
    [Features]
    Module Temperature Sensor (TSOD):Not Supported
    Module Nominal Height:29 - 30 mm
    Module Maximum Thickness (Front):1 - 2 mm
    Module Maximum Thickness (Back):1 - 2 mm
    Address Mapping from Edge Connector to DRAM:Standard


    from HWiNFO


  • gigs56din
    gigs56din Member Posts: 5

    Tinkerer

    Hi @robgc , thank you so much for the info. Well explained. 🙂
    This is the one that I bought. Hope everything will work. 




  • gigs56din
    gigs56din Member Posts: 5

    Tinkerer

    Correction @robgc this is the RAM that I bought. I already returned the one I bought in amazon (hyperX).

    Can you confirm if this is ok? It is the same brand and specs of the one that is pre-installed in my laptop. Many thanks bro.



  • robgc
    robgc Member Posts: 5

    Tinkerer

    gigs56din said:
    Correction @robgc this is the RAM that I bought. I already returned the one I bought in amazon (hyperX).

    Can you confirm if this is ok? It is the same brand and specs of the one that is pre-installed in my laptop. Many thanks bro.



    According to the datasheets here:

    https://www.skhynix.com/product/filedata/fileDownload.do?seq=11561

    https://www.skhynix.com/products.view.do?vseq=3359&cseq=75

    Yes the -WM version matches the 21-21-21-specifications and should be compatible running at DDR4-2933 CL21. 

    It is a different company than Micron.

    SK Hynix is a well known good quality memory company that is HQ in South Korea.

    Micron / Crucial are HQ in Idaho, USA. 

    From your comment above it seems the current memory module in your laptop is made by SK Hynix and not Micron? In that case it would be best to match it with the same brand like you have done. 

    Did you use the HWiNFO software or open it up and look inside to determine what module was already installed?





  • gigs56din
    gigs56din Member Posts: 5

    Tinkerer

    Hi @robgc, thanks for your prompt reply. Yes, the pre-installed RAM in my Acer Nitro is also SK Hynix but made in China. Nevertheless, still same brand.

    I opened my laptop and also installed CPU-Z as per your advice and saw that my CL is 21-21-21.

    It is more clearer to me now how my RAM works. Thanks a lot!
  • kd31967
    kd31967 Member Posts: 1 New User
    Hi Guys,  This is my Acer model - Acer Nitro 5 Intel Core i5-10th Gen 15.6-inch Display 1920 x 1080 Thin and Light Gaming Laptop (8GB Ram/1TB HDD + 256GB SSD/Windows 10 Home/GTX 1650Ti Graphics/Obsidian Black/2.3 Kgs), AN515-55

    This will support 32 gb ram. I am getting max capacity 8 GB. Please help i want to increase ram up 32 gb.

  • robgc
    robgc Member Posts: 5

    Tinkerer

    kd31967 said:
    Hi Guys,  This is my Acer model - Acer Nitro 5 Intel Core i5-10th Gen 15.6-inch Display 1920 x 1080 Thin and Light Gaming Laptop (8GB Ram/1TB HDD + 256GB SSD/Windows 10 Home/GTX 1650Ti Graphics/Obsidian Black/2.3 Kgs), AN515-55

    This will support 32 gb ram. I am getting max capacity 8 GB. Please help i want to increase ram up 32 gb.


    Sorry for the late reply :/ Just checked this thread by chance today.

    Your best bet would be to put in 2x 16GB modules:
    Crucial 16GB DDR4 3200 MT/s (PC4-25600) SODIMM 260-Pin Memory
    Part Name is CT16G4SFRA32A or CT16G4SFD832A