Aspire E5-475-Got freeze and goes to black screen after Acer logo and 'Preparing automatic repair'.

Ace249
Ace249 Member Posts: 8 New User
edited November 22 in Aspire Laptops
Hello

My laptop (Acer Aspire E5-475) running Windows 10 froze while I was using it, so I shut it down by holding down the power key for 5 seconds. When I turned the laptop back on, I got to the 'Acer' logo, but the screen then went black. I shut it down and turned it back on. The message 'Preparing automatic repair' was displayed but then went back to a black screen.

Background: I installed some updates (not sure which ones) about a week before the incident. I had been using the laptop since those updates with no difficulties at all so not sure if it is relevant.

Things I've tried:
  1. Pressed F2 after turning laptop on and enabled D2D and F12 Boot menu. This didn't appear to change anything
  2. Turned laptop off, and when turning back on pressed Alt + F10. A 'Please wait' message and a spinning disc displayed but then the screen went black again.
  3. Turned laptop off and unplugged it from mains, inserted a paperclip in the battery reset hole at the base of the laptop. Left for a few hours, plugged back in and turned on. The 'Acer' logo displayed and then the screen turned black again.
  4. When the black screen appears, I connected the laptop to a TV using a HDMI cable to make sure the screen wasn't faulty. 'No Signal' being displayed on the TV
Any help will be greatly appreciated.


Answers

  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    Get back into the BIOS menu and make sure the D2D and F12 options are still enabled. Then set and save a supervisor password in the BIOS security tab. Then re-enter the BIOS with the supervisor password and disable secure boot. Then shut the machine off. Then turn it back on and immediately start tapping the ALT+F10 to access the hidden recovery partition and try either a refresh while saving your personal files. Jack E/NJ

    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    Thanks for your reply. I have tried the above but upon pressing alt + f10 I get the 'Please Wait' message and then a black screen again, just like before. Anything else I can try? 
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    (1) Does the BIOS menu screens seem to behave OK?
    (2) Do you ever get an options menu with the ALT+F10 cold boot method before the screen goes black?

    Jack E/NJ

    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    The BIOS menu seems to be OK although I'm not very tech savvy. 
    Never got an options menu, goes from 'Please Wait' straight to black screen 
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    OK. Go to this link and prepare a USB installation stick using Microsoft's media creation tool. https://www.microsoft.com/en-us/software-download/windows10

    Tap the F12 key on startup to select the USB installation stick to see if you can boot to a recovery menu options screen instead of a black screen. We'll go from there if you can at least get to a recovery menu options screen.

    Jack E/NJ






    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    I followed the instructions and prepared the USB installation stick. It appeared in the F12 boot menu but when I try to boot from it I am stuck on the 'Acer' logo screen with a spinning disc. Anything else I can try? 
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    Try another USB port. If you used the USB port on the right side, this is a slow port and may take as much as 30 minutes to load. Jack E/NJ

    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    I plugged into the right side port and left for around 90 minutes. I have also tried the left port for about 30 minutes but I am still stuck on the 'Acer' logo screen
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    Press and hold the power button till the machine shuts off. Unplug the charger. Remove the USB stick. Gently press and hold a paperclip into the battery reset pinhole on the bottom for about 30 seconds. At the same time, press and hold the power button. Then plug the charger and Win10 installation stick back in again. Then turn the machine on and try the F12 routine again. Jack E/NJ


    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    Hi. I've tried the above but I still am stuck on the acer logo with spinning disc. I tried all 3 ports. Is there anything else I can try? 
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    Re-check the BIOS Boot tab to make sure secure boot is still disabled and the USB stick first in the boot order even ahead of WinBootMgr. Jack E/NJ

    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    Secure boot was already disabled. I moved the USB stick to the top of the boot priority order but still no luck... 
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    Disconnect the HDD and try to boot to an error or install screen from the stick. Jack E/NJ

    Jack E/NJ

  • Ace249
    Ace249 Member Posts: 8 New User
    How do I disconnect the HDD? Would disconnecting it delete all my files? 
  • JackE
    JackE ACE Posts: 44,889 Trailblazer
    Whatever files are still on the drive remain intact with the HDD disconnected. Unplug charger. Remove 4 screws from HDD cover and slide cover off. Then remove HDD cable. Put cover back on. Jack E/NJ




    Jack E/NJ

  • KillingKanzaki
    KillingKanzaki Member Posts: 1 New User

    To resolve the issue proceed with the following steps:

    1. Go into Safe Mode
    2. Delete the Intel Graphics Driver & Software (by ticking the box during deletion and ensuring the driver reverts to Microsoft Display Adapter)
    3. Reboot back into Windows​​​​​​​
    4. Update the BIOS
    5. Use the latest Intel Graphics Driver from the Acer website
    6. Update to Windows 10 20H2 minimum
  • Easwar
    Easwar Member Posts: 6,727 Guru
    Hi KillingKanzaki,

    Good to know thanks for your information. It will be useful for many people. 
  • SuhaibRoy
    SuhaibRoy Member Posts: 1 New User

    Hi, I am also facing the same issue, the acer logo appeared but then screen went black and now it is not turning on back. Can you please help me out.

  • JackE
    JackE ACE Posts: 44,889 Trailblazer

    Try booting from a Windows installation USB drive by tapping the F12 key on startup. Then use recovery option on the USB installation drive.

    Jack E/NJ