Aspire warning message

Oldvsnew
Oldvsnew Member Posts: 1 New User
edited September 2023 in 2019 Archives
I have a Acer aspire and haven't used it but maybe 3 times and it's been about 6 months since last used until I charged it all night few days ago and next day I get a warning dimm1 and dimm2. I have tried to reset battery and nothing changed. Please help. 

Best Answer

  • ram148280
    ram148280 Member Posts: 6

    Tinkerer

    Answer ✓
    1) Power the system off and connect the AC adapter and charge the system for 2 to 4 hours.
     
    2) Remove the DIMM Module (Should you have only one this is fine)
    Ensure your DIMMS are the matching modules (Same model number).
    press the power button on the laptop 15 times then hold it down for 30 seconds.
    Place the DIMMS back in their slots, close the door and replace the battery.
    Turn on the laptop and you should see the ACER logo

    hope it will help you

    ram Sharma

Answers

  • ram148280
    ram148280 Member Posts: 6

    Tinkerer

    Answer ✓
    1) Power the system off and connect the AC adapter and charge the system for 2 to 4 hours.
     
    2) Remove the DIMM Module (Should you have only one this is fine)
    Ensure your DIMMS are the matching modules (Same model number).
    press the power button on the laptop 15 times then hold it down for 30 seconds.
    Place the DIMMS back in their slots, close the door and replace the battery.
    Turn on the laptop and you should see the ACER logo

    hope it will help you

    ram Sharma
  • MaClane
    MaClane ACE Posts: 35,598 Trailblazer
    Good night Oldvsnew  !

    First, what exact model of your laptop?

    Perform the following procedures:

    CALIBRATION AND BATTERY RESET


    First, disable Quick Start in the power options and disconnect the notebook from the power outlet.


    httpswwwhowtogeekcomwp-contentuploads201602fast-startup-650x313pngpagespeedcekM3Qa70mcUpng

    BATTERY CONTROLLER RESET
    Access the device manager and look for the "acpi-compatible control method battery driver" and "microsoft AC adapter" and give it up.
    Then restart the notebook for Windows to reinstall and remove any errors.


    httpsimagesdrivereasycomwp-contentuploads201811img_5bfe7020cb7efjpg

    Process to reset the battery

        Disconnect the power adapter.
        Locate the hole to reset the battery in the bottom of the computer.
        He inserted a small clip into the hole. Hold the reset button for 05 seconds.
        Let the computer rest for 5 minutes without power.
        Plug in the power adapter and turn on the system.



    The button is the type that is identified in the photo.


    External Battery Pack

    If your notebook has an external battery, proceed as follows:
    1- Unplug the appliance from the mains and then disconnect the battery.
    2- Press the power button for thirty seconds, so that the static power is dissipated.
    3 - Replace the battery and turn the unit on.

    Process for calibrating the battery

    For this, you must turn off the device and give a 100% charge.
    Then unplug and use the battery until the battery runs out.
    Reload it as before.
    Repeat the process 3 times so that all cells are fully calibrated.

    POWER INTERRUPT BUTTON

    Make sure that the power interrupt button is pressed down:



    You can either press the right screw a little more or put some layers of electrical tape:




    Se minha resposta foi útil, deixe um Curtir, marque como Solucionado e clique em Promover!
    Caso contrario, fico a disposição para tentarmos sanar suas duvidas e resolver seus problemas!
    Atenciosamente:  J. MaClane™

    If my answer was helpful, leave a Like, flag as Fixed and click Promote!
    Otherwise, I am willing to try to heal your doubts and solve your problems!
    Sincerely, J. MaClane ™


    For users of the English, Spanish, French and German Community, I will be using Google Translate!