Acer Connect X6E bridge mode-want to use it as a 5G device but I only want to bring in Internet.

Freber
Freber Member Posts: 5

Tinkerer

edited April 8 in Gadgets & Accessories

Hi!
We have brand new Acer Connect X6E and I want to use it as a 5G device, but I only want to bring in Internet through it and then relay it to another internal firewall.

So how do I put it in bridge mode?

[Edited the topic title to include the topic issue.]

Answers

  • Sharanji
    Sharanji ACE Posts: 5,136 Pathfinder

    @Freber

    To use your Acer Connect X6E as a 5G device and only bring in internet, you'll need to configure it in bridge mode also known as "passthrough" or "router" mode) and then connect it to your existing router/firewall.

    Here's a breakdown of the process:
    Access the X6E's Web Interface:
    Connect to the X6E's Wi-Fi network or use an Ethernet cable.
    Open a web browser and go to the X6E's IP address (usually 192.168.76.1 or 192.168.1.1).
    Log in with the default username and password (usually found on a sticker on the device)

    Configure Bridge Mode: How to Use Your Predator Connect W6 as a Bridge

    Connect the X6E to your existing router/firewall's LAN port using an Ethernet cable. Ensure that your devices connected to your existing router/firewall have internet access.

    You can find more information in Acer Connect X6E 5G CPE user manual

    I hope this helps! If this was useful, please hit 'Yes' or 'Like'! Thanks! 😊

  • Freber
    Freber Member Posts: 5

    Tinkerer

    But I dont understand, what does a static IP have to do with bridge mode?

    We dont have static IP even.

  • billsey
    billsey ACE Posts: 36,035 Trailblazer

    Because the Connect X6E is a dual WAN device, it needs some way to decide which internet connection to use, in order to pass that data to your local network. That means it has to have NAT enabled between both the WAN ports and your local network, so doesn't support bridge mode. Instead, just use a NAT that doesn't conflict with your local network. So, you might set the NAT for DHCP on the 5G side and a static address of (for instance) 10.10.2.254/24 on the Ethernet side, with the DHCP server enabled and your normal router configured for DHCP WAN getting an address of something like 10.10.2.2 from the X6E. If you are doing port forwarding, just set the DMZ to your normal router and everything will get forwarded through.

    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Freber
    Freber Member Posts: 5

    Tinkerer

    I dont understand, does it support bridge mode or not if we dont have a static IP?

  • billsey
    billsey ACE Posts: 36,035 Trailblazer

    Static or dynamic doesn't make much difference. The key is that you need NAT (Network Address Translation) to deal with two IP subnets on the WAN side. Your local addresses have to be translated into addresses that the Internet sees, and that's done with the NAT functions. It sounds like your best options is like I suggested, Put the X6E on your incoming internet, with one side on your normal feed and the other on the 5G feed, then connect your current router to the LAN side of the X6E. Use either a static address for the router or allow it to get a dynamic address from the X6E, but configure the router as your DMZ, so everything goes to it without any changes other than NAT. That way to don't have to setup port forwarding for everything.

    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Freber
    Freber Member Posts: 5

    Tinkerer

    But we only use 5G, we dont have any other Internet and we want to send that incoming 5G to our other local firewall.

  • billsey
    billsey ACE Posts: 36,035 Trailblazer

    If you are only using 5G as your internet feed you still have NAT between the 5G provider and your local network. You also have NAT again with your existing router, but as I said, that shouldn't be an issue. If you want to have your existing router providing NAT from one ISP and the X6E providing NAT from the 5G provider you are going to bump into issues. Once or the other has to handle load balancing or failover from the two providers you your local clients. The X6E can do that by itself. Whether your existing router can is dependent on the make and model of router. If it does support it, you simply connect the LAN side of the X6E to the second WAN port on the router.

    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Freber
    Freber Member Posts: 5

    Tinkerer

    I just want to enable bridge mode, nothing else. Other routers I have worked with has that as a check box and then its done. It just sends the signal through.

    Guess Ill have to buy a new router for that it seems…

  • billsey
    billsey ACE Posts: 36,035 Trailblazer

    Yes, it sounds like the X6E wasn't the right choice for your environment.

    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.