Ram upgrade on PO3-630

pinkraisons
pinkraisons Member Posts: 7

Tinkerer

Good afternoon. I am trying to upgrade the ram in my PO3-630 and doesn't want to work. The ram I purchased is the same CL (22), voltage (1.2v), speed (3200) and not XMP ram. The original and new ram will work independently but not together. I have tried swapping the ram pair positions and it still doesn't work. Any suggestions?
original ram - AM2P32NC8W1-BCFS
new ram - CT2K16G4DFRA32A


Answers

  • Amrita123
    Amrita123 Member Posts: 8

    Tinkerer

    heello i am hardware network  enginerer.i can help you please explain me what exactly problem you are facing.
  • pinkraisons
    pinkraisons Member Posts: 7

    Tinkerer

    When I install all 4 ram modules the computer won't start. The motherboard gives a solid error beep and hangs.
  • pinkraisons
    pinkraisons Member Posts: 7

    Tinkerer

    If I install either pair or ram in either slot pairs on the motherboard they work. But together they won't.
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    edited November 2021
    Are both RAM kits of same size? Maybe the original one is 8 + 8Gb and the new one 16 + 16Gb. Even this can cause problems in some cases, but then again your manual says that you should be able to use 48Gb configuration. At least you should be able to use all of the RAM at a lower "safe" speed (most likely 2133, 2400 or 2600).

    Have you checked what CPU-Z says about each kit? Do they run at the same speed according to it? You can check this also in Windows Task Manager under Performance tab and Memory leaf. What does it say in Speed for both individual kits?

    Usually for any guarantee is to get four identical sticks. If the new kit is 16 + 16 and is running at the correct speed, I'd leave it at that. 32Gb is plenty for most tasks. But if you need more, well, I'm afraid you may have to order another kit, but even that might not work.
  • pinkraisons
    pinkraisons Member Posts: 7

    Tinkerer

    CPU-Z says 3200 for both.
  • billsey
    billsey ACE Posts: 34,645 Trailblazer
    Here is the matrix for installing ram:
    It looks like mixed sizes aren't supported under 32GB, but that might just be deciding to not populate little used combos.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • pinkraisons
    pinkraisons Member Posts: 7

    Tinkerer

    It wouldn't be under 32G. I have a pair of 16G and a pair of 8G.
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    edited November 2021
    May I know what you do with your PC? If your main use is playing games, in most cases you won't gain more performance by going over 32Gb. Even if you mainly edit 4K videos on your PC, I doubt you'll see much of a difference between 32 or 48/64Gbs of RAM. About 6K and 8K I'm not sure.

    But if you really need more RAM your best bet will be to sell those smaller sticks and get another identical 32Gb kit... and hope that it will work at full speed. ^^
  • pinkraisons
    pinkraisons Member Posts: 7

    Tinkerer

    I work in networking and when studying for Cisco certifications run EVE-ng. If I have ISE, AD, and a couple Firepowers running it eats RAM pretty quickly.
  • billsey
    billsey ACE Posts: 34,645 Trailblazer
    So you need to populate to 16, 8, 16, 8 in the slots, as shown in the 48GB section of that table.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • pinkraisons
    pinkraisons Member Posts: 7

    Tinkerer

    Yes, I did that. I also tried 8,16,8,16.
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    Here is a LINK to a thread about using 32Gb RAM sticks. Since that discussion is about PO3-620 and not 630, I don't know if it will help you or nor. But if you really need more RAM, maybe you can give it a try? Of course there is still that option of ordering another kit of those new RAM sticks you got.
  • RX2071
    RX2071 Member Posts: 1 New User
    Hi did you resolve this issue??,
    I am having the same issue with
    2x8gig (original 8gb1xrx8 pc4 2666v ua2- 11 ) &
    FURY KF426C16BBK2/16  1G x 64-bit (8GB) DDR4-2666 CL16 SDRAM 1Rx8,
    both work by themselves as a pair but not together?
    pc wont boot just beeps 
    cheers
  • billsey
    billsey ACE Posts: 34,645 Trailblazer
    The Kingston Fury is XMP memory and I don't believe XMP is supported at any of the overclock speeds in a PO3-630. Send them back and get normal 2666 memory.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.