CPU Cooler recommendations 3000 PO3-620

Fingarn
Fingarn Member Posts: 51 Devotee WiFi Icon
Anyone who can give recommendations on a CPU cooler for my Orion PO3-620. 

would a 

Best Answers

  • christy1
    christy1 Member Posts: 1,619 Community Aficionado WiFi Icon
    Answer ✓
    Fingarn said:
    Thank you @christy1. Good help. How many screws are there on the mtb? Any fixations I ought to know about to take it out?

    Check these
    Accept if its Helpful.   B)
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    Answer ✓
    The power button is on two of the pins on the eight pin power connector. It's the same as the older ATX supplies used, just on different pins. The 6 pin and 8 pin connectors both have three each +12V and GND, plus the Power Enable and GND on those two extra pins.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.

Answers

  • christy1
    christy1 Member Posts: 1,619 Community Aficionado WiFi Icon
    Accept if its Helpful.   B)
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    Excellent, any pictures and updates on how the upgrade goes is appreciated. I am a bit worried about removing motherboard because I heard it is really tightly fitted in the cabinet. So tips and tricks will be valuable! 
  • christy1
    christy1 Member Posts: 1,619 Community Aficionado WiFi Icon
    Fingarn said:
    Excellent, any pictures and updates on how the upgrade goes is appreciated. I am a bit worried about removing motherboard because I heard it is really tightly fitted in the cabinet. So tips and tricks will be valuable! 
    hope you get some idea.



    Accept if its Helpful.   B)
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    Thank you @christy1. Good help. How many screws are there on the mtb? Any fixations I ought to know about to take it out?
  • christy1
    christy1 Member Posts: 1,619 Community Aficionado WiFi Icon
    Answer ✓
    Fingarn said:
    Thank you @christy1. Good help. How many screws are there on the mtb? Any fixations I ought to know about to take it out?

    Check these
    Accept if its Helpful.   B)
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    @SeoulFinn Kudos! Very fine walkthrough.
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    @SeoulFinn I am about to order a Fractal Design Meshify 2 case. Based on your dissection of the po3 620 do you think the motherboard would fit into a normal atx typ case? What about the dimensions of the weirdly shaped mtb? Are the six screws placed in a standardized way? 
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    Fingarn said:
    @SeoulFinn I am about to order a Fractal Design Meshify 2 case. Based on your dissection of the po3 620 do you think the motherboard would fit into a normal atx typ case? What about the dimensions of the weirdly shaped mtb? Are the six screws placed in a standardized way? 
    Looks like Acer doesn't want me here. Too bad. Hope you had time to read my reply. So long and thanks for all the fish!
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    @GotBanned Oh that is a shame. Your upgrade guides were really good. What policies did you posts violate?
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    edited March 2021
    Now running Noctua NH-U9S and Noctua case fans front an back :-). Followed instructions by @gotbanned / @SeoulFinn . Trickiest part is prying the cpu back plate away. Some patience and a blunt bending instrument worked for me. Scared I would kill the main board while working the back plate but as said it actually worked. 
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    Good job!


    When I compared my similarly modified  Acer to an unmodified one, the CPU temps(*) the CPU temp difference was "only" 30C. When the unmodified PC's CPU hit 90C in a minute or two it started to throttle and lose performance. The modified one chugged on happily without any loss.



    (*) Intel Burn Test; Stress Level Maximum, Threads All
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    edited March 2021
    Tried moving the whole rig to a new case, but as expected I ran in to problems connecting the power cables from the new PSU to my PO3-620 main board. Couldn’t find matching power cables for the ACER Mainboard. There are three separate power connectors at the mainboard, none of them seem standardized?

    shout out; “Anyone who knows how to connect the PO3-620 motherboard to a standard PSU”
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    The PO3-620 uses an ATX12VO power supply. As the name suggests the supply provides only 12V DC power to the motherboard via those connectors. An old style ATX supply has a bunch of voltages, ranging from -12V through +12V, with 3.3V and 5V bits as well. Use the stock supply from your old case, they are physically the same size.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    Thx @billsey thats what I need to do. Just hope cable length will suffice. Fingers crossed.
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    If you flip your PSU upside down, you'll gain approx. 10cm cable length. Then you still have to figure out how to actually power up your system. :(

    (Sorry to sound like a broken record!)
  • Fingarn
    Fingarn Member Posts: 51 Devotee WiFi Icon
    edited March 2021
    I have not given up on the idea, yet... Have not thought about connecting the power button. Is that a proprietary thing as well?
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    Fingarn said:
    I have not given up on the idea, yet... Have not thought about connecting the power button. Is that a proprietary thing as well?
    That's the spirit!

    I can't remember exactly, but unfortunately I think it is. Maybe there is a way to mount Acer's power button to the new case? That is, if it can even be taken off in one piece. But don't worry too much; power button is the smallest hurdle you must overcome.
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    Answer ✓
    The power button is on two of the pins on the eight pin power connector. It's the same as the older ATX supplies used, just on different pins. The 6 pin and 8 pin connectors both have three each +12V and GND, plus the Power Enable and GND on those two extra pins.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
This discussion has been closed.