Acer Aspire 5 A515-51G "no bootable device" error.

Aleksandra00
Aleksandra00 Member Posts: 9 New User
Hey. I have an Acer Aspire 5 A515-51G laptop and the error "no bootable device". I tried to change UEFI to Legacy and change the boot order but it didn't help. I think I need to manually repair the boot partition. And here's my question - how to do it, because this laptop has unusual names of these partitions and I don't know which one it is responsible for.
 I would like to avoid installing the system from scratch. I tried to do it by bootrec /fixboot but it shows error "acces denied" . Please help ;_;.

«1

Answers

  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    Laptop BIOS must be set to UEFI mode. Does the HDD or SSD show up in the BIOS INFORMATION tab? Also make sure the D2D and F12 boot options are turned on in the BIOS MAIN tab. Jack E/NJ

    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    JackE said:
    Laptop BIOS must be set to UEFI mode. Does the HDD or SSD show up in the BIOS INFORMATION tab? Also make sure the D2D and F12 boot options are turned on in the BIOS MAIN tab. Jack E/NJ
    I checked it all yesterday and the same effect is still there. 
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    Does the HDD or SSD show up in the BIOS INFORMATION tab?  Jack E/NJ

    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    It's HDD WD Blue 1tb.i checked this too. 
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    This does not seem to be a factory installed Win10 since it was installed on an MBR-partitioned, not GPT-partitioned, HDD.  It won't boot in UEFI mode, only Legacy BIOS.  If it won't boot from Legacy, you must convert HDD to GPT partition, and re-install Win10 from the USB drive in UEFI mode. Jack E/NJ


    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    JackE said:
    This does not seem to be a factory installed Win10 since it was installed on an MBR-partitioned, not GPT-partitioned, HDD.  It won't boot in UEFI mode, only Legacy BIOS.  If it won't boot from Legacy, you must convert HDD to GPT partition, and re-install Win10 from the USB drive in UEFI mode. Jack E/NJ


    It is not possible to create a boot partition manually as if you were installing Windows manually?
    I looked through the hirens cd and all the files are there, maybe I could fix it without reinstalling and changing to gpt?
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    If you want to try to keep the HDD MBR partitioned with the Windows system on it now, volume 1 must be re-labelled the C letter. Volume 0 should NOT be labelled C. In fact, you should remove any assigned letters from Volume 0 and volume 2 as they are not necessary. 

    Jack E/NJ





    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    Ok. So I will fix this labels and then... I don't know. I think I must fix this with bootrec or something. What you think about that? 
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    Fix the labels first. Then make sure the BIOS is in legacy mode. If it still won't boot, then yes we will try to repair the ESP system reserved FAT32 partition using the USB Win installation drive's  X : \ windows\system32\>_ command prompt. Jack E/NJ

    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    I have repaired these labels but still display the same error. In UEFI mode "no bootable device" and in Legacy mode "an operating system wasn't found"
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    edited April 2020
    It must be in LEGACY mode before we proceed any further!!!!!!   Jack E/NJ

    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    It is in Legacy mode. ;<. The previous photo too. 
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    OK. Boot from the USB installation drive so you can get to the X : \windows\system32\>_ command prompt. Then enter the following 3 commands in the order presented. If you get any error messages after each command. STOP and report back.  Jack E/NJ

    bootrec /rebuildbdc

    bootrec /fixmbr

    bootrec /fixboot


    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    if I type "bootrec /fixboot" I have an error "access denied" 

  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    OK. Boot again from the USB installation stick. Now try automatic repair from the troubleshooting advanced option section. Jack E/NJ

    Jack E/NJ

  • Aleksandra00
    Aleksandra00 Member Posts: 9 New User
    Well ... XD worked. Simple solutions, however, are the best. Thank you so much.
  • JackE
    JackE ACE Posts: 45,081 Trailblazer
    Congrats on your success. Jack E/NJ

    Jack E/NJ

  • Hamtech
    Hamtech Member Posts: 13

    Tinkerer

    Pls I’m having same issue

  • Hamtech
    Hamtech Member Posts: 13

    Tinkerer

    bootable not found

  • I suggest you ask a new question and let me know your computer model. example PH315-52-5890.

    Oi! Eu não sou sou a cortana! Mas estou aqui para ajudar! Hi! I'm not the cortana! But I'm here to help!
    Se você gostou da minha resposta, marque como solução clicando em sim! If you liked my answer, mark it as a solution by clicking on yes!
    Aceite somente a resposta que ajudou a solucionar o seu problema! Please accept only the response that helped to solve your problem!
    Detection tool click here to find the serial number or partnumber of your model!                                                          
                                                      
                                                     egydiocoelho Trailblazer
     
    ProductKey clique aqui para descobrir o serial do windows! click here to discover the windows serial!
    Para usuários da comunidade inglesa, espanhola, francesa e alemã, usarei o google tradutor! :)
    For users of the English, Spanish, French and German community, I will be using google translator! :)