Acer d257 thermal pads replacement

Jalambakisa
Jalambakisa Member Posts: 4 New User
edited November 2023 in 2020 Archives
Don't know proper thickness and other parameters of thermal pads for this netbook.
Can you help me?

Answers

  • JackE
    JackE ACE Posts: 44,898 Trailblazer
    edited February 2020
    Actually, the pads are a silicone putty approved for use on this and other netbooks. Eapus XR-PE is recommended. There are other brands of  this putty Jack E/NJ


    Jack E/NJ

  • Jalambakisa
    Jalambakisa Member Posts: 4 New User
    JackE said:
    Actually, the pads are a silicone putty approved for use on this and other netbooks. Eapus XR-PE is recommended. There are other brands of  this putty Jack E/NJ


    So I can't use something like Pro Legend PL4202?
  • JackE
    JackE ACE Posts: 44,898 Trailblazer
    It would probably be OK. Are you having an overheating issue? Overheating is very rare for this type of netbook due to problems with thermal paste or pads. Overheating is usually caused by a fan and air intake/exhaust ports are clogged with dust and hair. It's best to alternately vacuum the air intake ports and blow air through the exhaust ports to dislodge this debris. I'd advise doing this first. Changing the pad & paste on the heat sink shouldn't be done until you've tried to vacuum and blow air thru the ports. Jack E/NJ 

    Jack E/NJ

  • Jalambakisa
    Jalambakisa Member Posts: 4 New User
    JackE said:
    It would probably be OK. Are you having an overheating issue? Overheating is very rare for this type of netbook due to problems with thermal paste or pads. Overheating is usually caused by a fan and air intake/exhaust ports are clogged with dust and hair. It's best to alternately vacuum the air intake ports and blow air through the exhaust ports to dislodge this debris. I'd advise doing this first. Changing the pad & paste on the heat sink shouldn't be done until you've tried to vacuum and blow air thru the ports. Jack E/NJ 
    It's hard to say. Usually the temperature of proc is around 50 degrees. I suppose it should be less. And I want to change because I haven't touch them since 2011.
  • JackE
    JackE ACE Posts: 44,898 Trailblazer
    >>>It's hard to say. Usually the temperature of proc is around 50 degrees. I suppose it should be less.>>>

    Absolutely not. Only 50*C!!!? You have no heat problem. Don't try to fix a non-issue. I haven't touched my AO722 netbook since 2011 either except for taking the bottom cover off and blowing the dust out in my backyard with a vacuum cleaner exhaust. I'm using it right now in my response to you. Jack E/NJ

    Jack E/NJ

  • Jalambakisa
    Jalambakisa Member Posts: 4 New User
    JackE said:
    >>>It's hard to say. Usually the temperature of proc is around 50 degrees. I suppose it should be less.>>>

    Absolutely not. Only 50*C!!!? You have no heat problem. Don't try to fix a non-issue. I haven't touched my AO722 netbook since 2011 either except for taking the bottom cover off and blowing the dust out in my backyard with a vacuum cleaner exhaust. I'm using it right now in my response to you. Jack E/NJ
    Thank you for answer, dude. I suppose, it is normal for netbooks. Just thought, that I could make it better.
  • JackE
    JackE ACE Posts: 44,898 Trailblazer
    Here's the CPU temp table for the d257 netbook. My AO722 is almost the same. 50*C is the lowest CPU temp before the fan will even kick in. Anything below about 85*C is considered normal for this netbook. Find something else to tinker with if you must.   :)   Jack E/NJ


    Jack E/NJ