I have a A1-810 (WW-GEN1) with 4.2.2. Is there any way to upgrade to 4.4 now ?

jackchui
jackchui Member Posts: 8 New User

 

I have downloaded the following file. Is it safe to install it on my tablet? I heard someone brick his tablet when installing this file.

 

 

OS_Acer_Acer.AV0K0.A1-810.RV0BRC01.WW.GEN1_A44K_A.zip

Answers

  • jackchui
    jackchui Member Posts: 8 New User

     

    By the way, on the ACER support web-site. only the upgrade file for the PA-CUS version is provided. Does this mean that the WW-GEN1 is stuck with 4.2.2. ?

  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer

    That one is correct:

    Acer.AV0K0.A1-810.RV0BRC01.WW.GEN1

     

    http://global-download.acer.com/GDFiles/OS/OS/OS_Acer_Acer.AV0K0.A1-810.RV0BRC01.WW.GEN1_A44K_A.zip?acerid=635500569872262266&Step1=TABLET&Step2=ICONIA%20A1&Step3=A1-810&OS=A12&LC=it&BC=ACER&SC=EMEA_17

     

    about bricking, can happen but this depends if you rooted your device or made any changes on system files.

    I'm not an Acer employee.
  • jackchui
    jackchui Member Posts: 8 New User

     

    Thanks for the prompt reply.

     

    I went ahead and installed the update. Unfortunately it ended in disaster.

     

    After flashing the zip file.  The tablet rebooted and went into a reboot loop. I pressed volume up and power buttons together  to stop it and re-do the installation. This time after reboot the tablet gave a black screen and never respond again no matter what button I pressed

     

    I inserted a paper clip into the reset hole but there was no response at all.   The tablet was totally dead.

  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer
    Connect the AC charger, then press power button + volume up to enter recovery and try a factory data reset.
    http://acer--uk.custhelp.com/app/answers/detail/a_id/32849/~/factory-data-reset-on-acer-iconia-a1-830
    I'm not an Acer employee.
  • jackchui
    jackchui Member Posts: 8 New User

    No luck.

     

    Cannot wake the tablet up.

     

     

  • billsey
    billsey ACE Posts: 34,234 Trailblazer

    If you didn't get the file directly from Acer, you have no idea what's in there. Smiley Sad

    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer

    if you are still under warranty, contact the Acer support service.

    I'm not an Acer employee.
  • jackchui
    jackchui Member Posts: 8 New User

     

     

    1.   The update file was downloaded from ACER website.

     

    2.   The tablet is already out of warranty.

  • jackchui
    jackchui Member Posts: 8 New User

     

    Is there any way to do a cold reset ?

  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer
    Nope. Check your private messages.
    I'm not an Acer employee.
  • hsvstar2003
    hsvstar2003 Member Posts: 1 New User

    I hope its OK to post my problem here since it is pretty much exatcly the same.

     

    I also have an Acer A1-810 and because i never got any update prompts I wen to

    http://www.acer.de/ac/de/DE/content/drivers

     

    and downloaded the Acer.AV0K0.A1-810.RV0BRC01.WW.GEN1 OS.

     

    After installing it in Recovery mode the Tablet would not boot. It just showed the acer logo indefinitely.

     

    So  then I went ahead and downloaded Acer.AV052.A1-810.RV31RC03.WW.GEN1 so that I can at least go back to 4.2 Jelly Bean.

    But after flashing I am now stuck in a Bootloop. Factory reset/wipe data is not helping.

     

    Any ideas on what I should do?

     

    Edit: My stock firmware should be for RV18RC07. But I cannot find it on the Acer website

  • IronFly
    IronFly ACE Posts: 18,413 Trailblazer

    probably trying to flash back to 4.2, you mixed the bootloader and now can't boot correctly.

     

    if you are under warranty, contact Acer support service, if not.....send me a private message.

    I'm not an Acer employee.
  • jackchui
    jackchui Member Posts: 8 New User

     

    I returned the unit to ACER service centre and they asked for nearly U$200 to repair it.  This is just ridiculous.

     

    Given so many people got this problem, I suspect this is an inherent problem of ACER's upgrading software.