Remove cpu from PO3 620

Personal1012
Personal1012 Member Posts: 6

Tinkerer

Hi guys I have a quick question, I recently bought the po3 620 and my question is: can I remove the cpu from that motherboard a me out it on a new one?

Answers

  • Personal1012
    Personal1012 Member Posts: 6

    Tinkerer

    And put it*
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    Sure, as long as the new one supports the same CPU. Remember that most MBs only support one generation of CPUs, even if the socket is the same, due to the rest of the timing clocks.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Personal1012
    Personal1012 Member Posts: 6

    Tinkerer

    billsey said:
    Sure, as long as the new one supports the same CPU. Remember that most MBs only support one generation of CPUs, even if the socket is the same, due to the rest of the timing clocks.
    Thank you so much for the fast response 😊👍🏻
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    "Put it on a new one"?

    Sorry but I haven't had my morning coffee yet, but... Are you planning on swapping your CPU to a faster one or using your current CPU on another motherboard? What CPU or CPUs are we talking about?
  • Personal1012
    Personal1012 Member Posts: 6

    Tinkerer

    Good morning, no worries. My question is: can I remove the i7 10700 from the acer motherboard to install it on a now motherboard? 
  • A7max96
    A7max96 Member Posts: 9

    Tinkerer

    Hi guys I have a quick question, I recently bought the po3 620 and my question is: can I remove the cpu from that motherboard a me out it on a new one?
    you cant but another motherbord in this case acer predator p03-620 

  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    Thanks for getting back to me. Yes, you can remove the CPU from Acer and mount it on another motherboard. I did this and my CPU is happily working on a MSI B560 Tomahawk WiFi motherboard, which supports both 10th and 11th gen Intel processors.

    But by I had to get a new case and PSU for this to work.
  • Personal1012
    Personal1012 Member Posts: 6

    Tinkerer

    GotBanned said:
    Thanks for getting back to me. Yes, you can remove the CPU from Acer and mount it on another motherboard. I did this and my CPU is happily working on a MSI B560 Tomahawk WiFi motherboard, which supports both 10th and 11th gen Intel processors.

    But by I had to get a new case and PSU for this to work.
    Ohhh nice thank you so much, another one: can i7 10700 and a b560 support ram at 3200 MHz? Because I'm seeing that this is not supported 
  • Leostat
    Leostat ACE Posts: 3,043 Pathfinder
    Not nativly, tops out at 2933 JEDEC speeds, above that is XMP which depends on the board (The acer one does not support it :) )
  • Personal1012
    Personal1012 Member Posts: 6

    Tinkerer

    Leostat said:
    Not nativly, tops out at 2933 JEDEC speeds, above that is XMP which depends on the board (The acer one does not support it :) )
    Thank you so much, but will a b560 support it? I talk about the AsRock b560 pro4
  • Leostat
    Leostat ACE Posts: 3,043 Pathfinder
    edited June 2021
    Should do, pretty much any third party baord will expose overclocking / XMP options :)  looking at the manual it says it does anyway on pages 2 and 58:

    https://download.asrock.com/Manual/B560 Pro4.pdf
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    edited June 2021
    I can speak only about the MSI board, but I don't see why all B560s wouldn't support DDR4-3200 and more. Some are supposed to support speeds upto DDR4-5066 if I'm not mistaken. But 3200 is already plenty fast.

    The original Kinsgston 2x8Gb RAM from P03-620 was automatically set to run at DDR4-3200 speeds. I didn't even enable XMP because the board did it by itself after few reboots. Reboots were needed because I transplanted parts from Acer to a MSI mobo (different chipsets, drivers, etc.) and didn't even bother ro reinstall Windows. Why you ask me? Well, because all was in working order BEFORE my friend tore out the only full length PCIE slot from the board while removing the GPU. *sigh* Yes, there's a latch that has to be opened. He learned this the hard way!
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    Man, he must have arms like a gorilla... :)
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • GotBanned
    GotBanned Member Posts: 654 Seasoned Specialist WiFi Icon
    Haha! He's a skinny middle-aged man and almost no experience in building computers.

    Because he didn't open the PCIE latch the "other end was stuck". He decided to wiggle the card and lo and behold, the card came out in no time... with the PCIE slot still attached to it!

    The new board has metal enforced slot(s), but I'm sure he has learned his lesson and won't make it again. ^^
  • billsey
    billsey ACE Posts: 34,601 Trailblazer
    Let's hope he passes his hard won skillz on to others. :)
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.