acer aspire e 11 laptop won't start and blinking blue light

Natsu3567
Natsu3567 Member Posts: 13

Tinkerer

my acer aspire E 11 won't start when i press the power button it won't there is a blinking blue light 
and some times there is a sound cames from battery or speaker idk pls help
«1

Answers

  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Press and hold power button until all lights are dark. Then remove charger. Then insert paperclip into pinhole on bottom for 30 seconds. Then plug charger back in but wait for the battery charge light to turn from steady orange to steady blue. Then try to turn it on again.

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    thank you for your ansver but it did't help . when i use charcer the orange light is steady but blue light is not affected 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Is the blinking blue light the battery charge LED or the power LED?

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    power led i think cause when i use the charger orange light is steady 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Wait till charger orange light turns to steady blue before you try to turn it on. This may take several hours. Maybe even overnight. If the battery charge LED doesn't turn steady blue  then the battery has probably failed and  needs to be replaced. Usually about $24USD for most e11 models.

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    i hope it works thank you
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    I'll keep my fingers crossed that it works for you.   :)   Jack E/NJ

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    it didn't work when i use charger charging light is all blue but the other light is still blinking like before there is no light in screen no sound from hard drive or any sign of living D;
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Did this seem to happen suddenly for no apparent reason?

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    actually i gave it to my friend and she said she tried to change harddrive to ssd but she had m.2 so she couldn't after that this problem occured idk what is happened i learned  it 5 mins ago 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Did it happen before or after yoou gave it to your friend?

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    after i gave it to her. she said she removed harddrive and put it back
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    That probably explains it. Better check to make sure the hard drive's connector is fully inserted to its mainboard socket.

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    everything is in its place but there is no sign of living when i press the power button power led is blinking thats it no light from screen no sound i don't want to think it is dead 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    Reseat the HDD connections a few times anyway to help clean its contacts. It might also be a good idea to reseat all the other accessible components like RAM module if so equipped. If she indeed tried to install an m.2 card, you probably should remove the bottom cover for a more thorough examination of other ribbon connectors to the mainboard. Some of them are rather small, easy to miss a disconnection and use a rather flimsy sliding wedge to keep them in place on the mainboard. Also, it is imperative that the battery be disconnected from the mainboard immediately after removing the bottom cover as live circuits are exposed.

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    edited June 2021
    all the cables are intact hard drive is in its place but it doesn't work
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    (1) Was the battery disconnected when trying to install the m.2 card?
    (2) Was an ESD wrist protector used when trying to install the m.2 card?

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    rn i controlled everything and pressed the power button but there is no change 
  • JackE
    JackE ACE Posts: 45,080 Trailblazer
    What is full ACER E11 model number? For example, E3-111? ES1-132?

    Jack E/NJ

  • Natsu3567
    Natsu3567 Member Posts: 13

    Tinkerer

    jack thank you for your time but i learned rn motherboard is dead . only possible solution rn is buying a new motherboard for it i think . btw model number is E3-112-C37C