Nitro ANV15-51 Nitrosense buggy, fan not spinning, no mode available, cannot control fan speed

Hi, I bought Nitro ANV15-51 during July last year. 1 week after buying, Nitrosense app was running into issue already: fan not spinning + app as good as useless since any clicking wasn't resulting in any function. I brought to my country's service centre, but same issue happened again few days later.

At that point, I figured that a temporary fix was to just re-install Nitrosense app even though we as consumers shouldn't have to be troubled into doing as that's not how the app should be functioning.

Anyways, I just re-installed it everytime it happened, until the most recent update to Nitrosense where I believe they tried to fix the issue. However, it only lasted a week for me before the issue happened again. Now re-installing Nitrosense doesn't work either, so not only did Acer NOT fix the issue, they also made the temporary fix broken.

I have tried re-installing Nitrosense, checking for any Windows update, running the cmd "lodctr /R", and basically any plausible method I could find online, but the app is still not working (I can hear the fan spinning but I cannot control it through app).

Please advise what do I do now, but I will NOT do a factory reset because as a consumer, I should not be troubled into doing that as a result of the company's failure in making a well-functioning software. I also tried using the previous Nitrosense version but it would just say "MUI_OPERATING_MODE_UNDEFINED".

TL;DR
Nitrosense not working: Laptop temperature and fan running speed not detected, no mode available, cannot control fan speed, re-installing or running "lodctr /R" no longer fix the issue.

[Edited the thread to add issue detail]

Accepted answers

eGomes

Welcome @CZE,

Try Windows Performance Counter reset:

1) Close the NitroSense app;

2) Open a Command Prompt / Windows Terminal (Administrator mode);

3) Type these commands (copy & paste):

%SystemRoot%\System32\lodctr.exe /R
%SystemRoot%\SysWow64\lodctr.exe /R
winmgmt.exe /RESYNCPERF

4) Restart your computer.

All comments

StevenGen

https://community.acer.com/en/discussion/725595/nitro-anv15-51-nitrosense-buggy

I symmetrize with you as the Nitro Sense app has been problematic for a long time post my 2020 Nitro AN515-56 version, as on that model laptop Nitro Sense worked 100% for me at the beginning, but in some circumstances and later on with Win-11 updates and a clean install, the setup.exe didn't work for the app and I needed to install this app within its folder for it to install and be triggered from the keyboard NS key.

I don't know the solution for your NS problem but try and see if you can install NS within its folder .exe instead of from its setup.exe. as that is how I solved the installation problem for my Nitro AN515-56. Good luck.

If this answers your question and solved your query please "Click on Yes" or "Click on Like" if you find my answer useful👍

CZE

https://community.acer.com/en/discussion/comment/1343456#Comment_1343456

Hi, how do I install it within it's folder? Isn't setup.exe within it's folder as well?

eGomes

Welcome @CZE,

Try Windows Performance Counter reset:

1) Close the NitroSense app;

2) Open a Command Prompt / Windows Terminal (Administrator mode);

3) Type these commands (copy & paste):

%SystemRoot%\System32\lodctr.exe /R
%SystemRoot%\SysWow64\lodctr.exe /R
winmgmt.exe /RESYNCPERF

4) Restart your computer.

CZE

https://community.acer.com/en/discussion/comment/1343458#Comment_1343458

OMG, that worked for me, once restarted, the fan is detected and the modes are available and the fans respond to what I select.

Thanks for the help.

Axxo

If your Nitrosense fan service isn't working, try reinstalling the software from the Acer website. Ensure you've disabled fast startup and consider a system restore or removing any potential antivirus conflicts. You may also need to update your BIOS, check for loose cable connections, and verify proper ventilation.

alecs_braicu

@eGomes I have the same problem here. I tried everything, reinstall multiple times but won't work. Now i tried your version with cmd comand. I tried 3 times, restart the computer and nothing. The app is still blocked. In the app I have a warning message that said something like: You need your computer to be 40% battery and on charge in order to switch modes. My laptop is on charge and at 80% now :). If you have a suggestion please. Thanks