Hello! I've upgraded BIOS to 2.11 and installed Windows 10 on my Acer V3-571G. It works good but it would work even better if I'd have more RAM. I installed CPU-Z and here's my specification about memory:
Chipset
-------------------------------------------------------------------------
Northbridge Intel Ivy Bridge rev. 09
Southbridge Intel HM77 rev. 04
Graphic Interface PCI-Express
PCI-E Link Width x16
PCI-E Max Link Width x16
Memory Type DDR3
Memory Size 4 GBytes
Channels Single
Memory Frequency 798.1 MHz (1:6)
CAS# latency (CL) 11.0
RAS# to CAS# delay (tRCD) 11
RAS# Precharge (tRP) 11
Cycle Time (tRAS) 28
Command Rate (CR) 1T
Host Bridge 0x0154
MCHBAR I/O Base address 0x0FED10000
MCHBAR I/O Size 19456
MCHBAR registers
Memory SPD
-------------------------------------------------------------------------
DIMM # 1
SMBus address 0x52
Memory type DDR3
Module format SO-DIMM
Manufacturer (ID) Hyundai Electronics (AD000000000000000000)
Size 4096 MBytes
Max bandwidth PC3-12800 (800 MHz)
Part number HMT451S6MFR8C-PB
Serial number 4F207E07
Manufacturing date Week 40/Year 12
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP no
AMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 5.0-5-5-14-19 @ 380 MHz
JEDEC #2 6.0-6-6-16-22 @ 457 MHz
JEDEC #3 7.0-7-7-19-26 @ 533 MHz
JEDEC #4 8.0-8-8-22-30 @ 609 MHz
JEDEC #5 9.0-9-9-24-33 @ 685 MHz
JEDEC #6 10.0-10-10-27-37 @ 761 MHz
JEDEC #7 11.0-11-11-28-39 @ 800 MHz
DMI
-------------------------------------------------------------------------
DMI BIOS
vendor Acer
version V2.21
date 12/16/2013
ROM size 3584 KB
DMI System Information
manufacturer Acer
product Aspire V3-571G
version V2.21
serial NXM67EP003248064E83400
UUID {F14926F3-0932-E211-8F52-B888E3ABE657}
SKU Aspire V3-571G_0648_V2.21
family Type1Family
DMI Baseboard
vendor Acer
model VA50_HC_CR
revision Type2 - Board Version
serial NBM6A110012483FF623400
DMI System Enclosure
manufacturer Acer
chassis type Notebook
chassis serial NXM67EP003248064E83400
DMI Processor
manufacturer Intel(R) Corporation
model Intel(R) Core(TM) i5-3230M CPU @ 2.60GHz
clock speed 2600.0 MHz
FSB speed 100.0 MHz
multiplier 26.0x
DMI Memory Controller
correction unknown
Max module size 8192 MBytes
DMI Memory Module
designation DIMM0
DMI Memory Module
designation DIMM1
DMI Memory Module
designation DIMM1
size 4096 MBytes (single bank)
DMI Memory Module
designation DIMM3
DMI Extension Slot
designation J5C1
type AA
populated no
DMI Extension Slot
designation J6C1
type A6
populated no
DMI Extension Slot
designation J6C2
type A6
populated no
DMI Extension Slot
designation J6D2
type A6
populated no
DMI Extension Slot
designation J7C1
type A6
populated no
DMI Extension Slot
designation J7D2
type A6
populated no
DMI Extension Slot
designation J8C1
type A6
populated no
DMI Extension Slot
designation J8C2
type AA
populated no
DMI OEM Strings
string[0] String1 for Original Equipment Manufacturer
string[1] String2 for Original Equipment Manufacturer
string[2] String3 for Original Equipment Manufacturer
string[3] String4 for Original Equipment Manufacturer
string[4] String5 for Original Equipment Manufacturer
DMI Physical Memory Array
location Motherboard
usage System Memory
correction None
max capacity 32768 MBytes
max# of devices 4
DMI Memory Device
designation DIMM0
format DIMM
type unknown
DMI Memory Device
designation DIMM1
format DIMM
type unknown
DMI Memory Device
designation DIMM1
format SODIMM
type unknown
total width 64 bits
data width 64 bits
size 4096 MBytes
DMI Memory Device
designation DIMM3
format DIMM
type unknown
I'd like to ADD at least 4 GB of RAM so I can have 8GB in total. I need to know is it possible to get RAM with higher frequency and will it work in my laptop. For instance can I remove current RAM (which is 800MHz) and install 2x4GB 1600 MHz? If not then what is max amount and speed of memory I can get? Id like to get a memory with better CLs if possible, can I do that?
Thank you, merry Christmas!
