Acer
Predator
ConceptD
Planet9
Altos R360F4如何設定INTEL INTEGRATED RAID MODULE - Acer Community
<main> <article class="userContent"> <h3 data-id="set-raid-controller-in-efi-mode-or-legacy-mode">Set RAID Controller in EFI Mode or Legacy Mode</h3><h3></h3><h3 data-id="1.-please-press-f2-to-enter-bios-setup-during-post.">1. Please press F2 to enter BIOS Setup during POST.</h3><h3 data-id="-1"></h3><h3 data-id="2.-please-press-f9-to-load-default-bios-settings.">2. Please press F9 to load default BIOS settings.</h3><h3 data-id="-2"></h3><h3 data-id="3.-in-main-page-change-quiet-boot-from-enabled-to-disabled.">3. In Main Page, change Quiet Boot from Enabled to Disabled.</h3><h3 data-id="-3"></h3><h3 data-id="quiet-boot-disabled">Quiet Boot [Disabled]</h3><h3 data-id="-4"></h3><h3 data-id="4.-in-boot-maintenance-manger-page-select-advanced-boot-options">4. In Boot Maintenance Manger Page, select Advanced Boot Options</h3><h3 data-id="-5"></h3><h3 data-id="5.-you-would-see-below-information.">5. You would see below information.</h3><h3 data-id="-6"></h3><h3 data-id="boot-mode-uefi">Boot Mode [UEFI]</h3><h3 data-id="-7"></h3><h3 data-id="6.-to-enable-legacy-mode-please-change-the-setting-to-legacy.">6. To enable legacy mode, please change the setting to Legacy.</h3><h3 data-id="-8"></h3><h3 data-id="boot-mode-legacy">Boot Mode [Legacy]</h3><h3 data-id="-9"></h3><h3 data-id="7.-to-enable-efi-mode-please-change-the-setting-to-uefi.">7. To enable EFI mode, please change the setting to UEFI.</h3><h3 data-id="-10"></h3><h3 data-id="boot-mode-uefi-1">Boot Mode [UEFI]</h3><h3 data-id="-11"></h3><h3 data-id="8.-press-f10-to-save-the-setting-and-exit-from-bios-setup.">8. Press F10 to save the setting and exit from BIOS Setup.</h3><h3 data-id="-12"></h3><h3 data-id="efi-mode">EFI Mode</h3><h3 data-id="-13"></h3><h3 data-id="entering-raid-efi-utility-(efi-mode)">Entering RAID EFI Utility (EFI Mode)</h3><h3 data-id="-14"></h3><h3 data-id="please-press-f2-to-enter-bios-setup-during-post.-in-bios-setup-select-advanced-pci-configuration-uefi-option-rom-control-storage-controller-to-configure-intel-integrated-raid-in-efi-mode.">Please press F2 to enter BIOS Setup during POST. In BIOS Setup, select Advanced > PCI Configuration > UEFI Option ROM Control > Storage Controller to configure Intel Integrated RAID in EFI mode.</h3><div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035.jpg" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035.jpg" alt="F201910035.jpg" height="180" width="320" loading="lazy"></img></a> </div> </div> <p></p><p><br></p><p><br></p><h3 data-id="loading-factory-default-setting-(efi-mode)">Loading Factory Default Setting (EFI Mode)</h3><h3 data-id="-15"></h3><h3 data-id="1.-select-main-menu-controller-management-advanced-controller-management.">1. Select Main Menu > Controller Management > Advanced Controller Management.</h3><h3 data-id="-16"></h3><h3 data-id="2.-select-set-factory-defaults.">2. Select Set Factory Defaults.</h3><h3 data-id="-17"></h3><h3 data-id="3.-check-confirm-and-then-select-yes.">3. Check Confirm and then select Yes.</h3><h3 data-id="-18"></h3><h3 data-id="4.-select-ok-and-then-press-f10-to-save-the-change.">4. Select OK and then press F10 to save the change.</h3><h3 data-id="-19"></h3><h3 data-id="creating-a-raid-volume-(efi-mode)">Creating a RAID Volume (EFI Mode)</h3><h3 data-id="-20"></h3><h3 data-id="1.-select-main-menu-configuration-management-create-virtual-drive.">1. Select Main Menu > Configuration Management > Create Virtual Drive.</h3><div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035-1.jpg" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035-1.jpg" alt="F201910035-1.jpg" height="180" width="320" loading="lazy"></img></a> </div> </div> <p></p><p><br></p><p><br></p><p> </p><h3 data-id="-21"> </h3><h3 data-id="2.-select-the-raid-level-desired-and-enter.">2. Select the RAID Level desired and Enter.</h3><h3 data-id="-22"></h3><h3 data-id="3.-select-select-drives-for-the-virtual-drive-and-apply-the-changes">3. Select Select Drives for the virtual drive and apply the changes</h3><h3 data-id="-23"></h3><h3 data-id="4.-specify-the-virtual-drive-size.">4. Specify the virtual drive size.</h3><h3 data-id="-24"></h3><h3 data-id="5.-select-save-configuration.">5. Select Save Configuration.</h3><h3 data-id="-25"></h3><h3 data-id="6.-check-confirm-and-then-select-yes.">6. Check Confirm and then select Yes.</h3><h3 data-id="-26"></h3><h3 data-id="7.-select-ok.">7. Select OK.</h3><h3 data-id="-27"></h3><h3 data-id="8.-press-esc-to-return-to-top-menu.">8. Press Esc to return to top menu.</h3><h3 data-id="-28"></h3><h3 data-id="initializing-a-raid-volume-(efi-mode)">Initializing a RAID Volume (EFI Mode)</h3><h3 data-id="-29"></h3><h3 data-id="1.-select-main-menu-virtual-drive-management-virtual-drive-that-you-just-created.">1. Select Main Menu > Virtual Drive Management > Virtual Drive that you just created.</h3><h3 data-id="-30"></h3><h3 data-id="2.-select-operation-by-enter.">2. Select Operation by Enter.</h3><h3 data-id="-31"></h3><h3 data-id="3.-select-fast-initialization.">3. Select Fast Initialization.</h3><h3 data-id="-32"></h3><h3 data-id="4.-select-go.">4. Select Go.</h3><h3 data-id="-33"></h3><h3 data-id="5.-check-confirm-and-then-select-yes.">5. Check Confirm and then select Yes.</h3><h3 data-id="-34"></h3><h3 data-id="6.-select-ok.">6. Select OK.</h3><h3 data-id="-35"></h3><h3 data-id="7.-press-esc-to-return-to-top-menu.">7. Press Esc to return to top menu.</h3><h3 data-id="-36"></h3><h3 data-id="assigning-a-hot-spare-drive-(efi-mode)">Assigning a Hot Spare Drive (EFI Mode)</h3><h3 data-id="-37"></h3><h3 data-id="1.-select-main-menu-drive-management-drive-that-you-want-to-assign.">1. Select Main Menu > Drive Management > Drive that you want to assign.</h3><h3 data-id="-38"></h3><h3 data-id="2.-select-operation-by-enter">2. Select Operation by Enter</h3><h3 data-id="-39"></h3><h3 data-id="3.-select-assign-global-hot-spare-drive.">3. Select Assign Global Hot Spare Drive.</h3><h3 data-id="-40"></h3><h3 data-id="4.-select-go.-1">4. Select Go.</h3><h3 data-id="-41"></h3><h3 data-id="5.-check-confirm-and-then-select-yes.-1">5. Check Confirm and then select Yes.</h3><h3 data-id="-42"></h3><h3 data-id="6.-select-ok.-1">6. Select OK.</h3><h3 data-id="-43"></h3><h3 data-id="7.-press-esc-to-return-to-top-menu">7. Press Esc to return to top menu</h3><h3 data-id="-44"></h3><h3 data-id="8.-press-f10-to-save-the-change-and-exit-bios-setup.">8. Press F10 to save the change and exit BIOS Setup.</h3><h3 data-id="legacy-mode">Legacy Mode</h3><h3 data-id="-45"></h3><h3 data-id="entering-raid-bios-utility-(legacy-mode)">Entering RAID BIOS Utility (Legacy Mode)</h3><h3 data-id="-46"></h3><h3 data-id="please-press-ctrl-r-when-you-see-the-raid-bios-during-post.-after-post-finished-the-intel-integrated-raid-module-bios-configuration-utility-will-show-on-the-screen.">Please press CTRL-R when you see the RAID BIOS during POST. After POST finished, the Intel Integrated RAID Module BIOS Configuration Utility will show on the screen.</h3><div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035-2.jpg" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035-2.jpg" alt="F201910035-2.jpg" height="180" width="320" loading="lazy"></img></a> </div> </div> <p></p><p><br></p><p><br></p><h3 data-id="loading-factory-default-setting-(legacy-mode)">Loading Factory Default Setting (Legacy Mode)</h3><h3 data-id="-47"></h3><h3 data-id="1.-in-the-top-menu-please-press-ctrl-n-to-switch-to-ctrl-mgmt-page.">1. In the top menu, please press Ctrl-N to switch to Ctrl Mgmt page.</h3><h3 data-id="-48"></h3><h3 data-id="2.-press-tab-to-move-the-cursor-to-set-factory-defaults-and-then-press-enter.">2. Press Tab to move the cursor to Set Factory Defaults and then press Enter.</h3><h3 data-id="-49"></h3><h3 data-id="3.-select-ok-to-load-factory-defaults.">3. Select OK to load factory defaults.</h3><h3 data-id="-50"></h3><h3 data-id="4.-press-ctrl-s-to-save-the-change.">4. Press Ctrl-S to save the change.</h3><h3 data-id="-51"></h3><h3 data-id="5.-press-esc-and-then-select-ok-to-exit.">5. Press Esc and then select OK to exit.</h3><h3 data-id="-52"></h3><h3 data-id="6.-press-ctrl-%2B-alt-%2B-del-to-reboot-the-server.">6. Press Ctrl + Alt + Del to reboot the server.</h3><h3 data-id="-53"></h3><h3 data-id="creating-a-raid-volume-(legacy-mode)">Creating a RAID Volume (Legacy Mode)</h3><h3 data-id="-54"></h3><h3 data-id="1.-on-the-vd-mgmt-page-of-top-menu-please-move-cursor-to-the-root-of-intel">1. On the VD Mgmt page of top menu, please move cursor to the root of Intel</h3><h3 data-id="-55"></h3><h3 data-id="integrated-raid.">Integrated RAID.</h3><h3 data-id="-56"></h3><h3 data-id="2.-press-f2-and-select-create-virtual-drive.">2. Press F2 and select Create Virtual Drive.</h3><div class="embedExternal embedImage display-large float-none"> <div class="embedExternal-content"> <a class="embedImage-link" href="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035-3.jpg" rel="nofollow noreferrer noopener ugc" target="_blank"> <img class="embedImage-img" src="https://us.v-cdn.net/6029997/uploads/migrated/acer_final/65638/F201910035-3.jpg" alt="F201910035-3.jpg" height="180" width="320" loading="lazy"></img></a> </div> </div> <p></p><p><br></p><p><br></p><h3 data-id="3.-select-the-raid-level-desired-by-enter.">3. Select the RAID Level desired by Enter.</h3><h3 data-id="-57"></h3><h3 data-id="4.-select-drives-for-the-virtual-drive.">4. Select Drives for the virtual drive.</h3><h3 data-id="-58"></h3><h3 data-id="5.-specify-the-size.">5. Specify the size.</h3><h3 data-id="-59"></h3><h3 data-id="6.-select-ok.-2">6. Select OK.</h3><h3 data-id="-60"></h3><h3 data-id="7.-select-ok-to-create-the-virtual-drive.">7. Select OK to create the virtual drive.</h3><h3 data-id="-61"></h3><h3 data-id="initializing-a-raid-volume-(legacy-mode)">Initializing a RAID Volume (Legacy Mode)</h3><h3 data-id="-62"></h3><h3 data-id="1.-locate-the-cursor-on-virtual-drive-0-you-just-created-and-then-press-f2.">1. Locate the cursor on Virtual Drive 0 you just created and then press F2.</h3><h3 data-id="-63"></h3><h3 data-id="2.-select-initialization-fast-init.">2. Select Initialization > Fast Init.</h3><h3 data-id="-64"></h3><h3 data-id="3.-select-yes.">3. Select Yes.</h3><h3 data-id="-65"></h3><h3 data-id="4.-press-ok-when-initialization-is-complete.">4. Press OK when initialization is complete.</h3><h3 data-id="-66"></h3><h3 data-id="assigning-a-hot-spare-drive-(legacy-mode)">Assigning a Hot Spare Drive (Legacy Mode)</h3><h3 data-id="-67"></h3><h3 data-id="1.-in-the-top-menu-please-press-ctrl-n-to-switch-to-pd-mgmt-page.">1. In the top menu, please press Ctrl-N to switch to PD Mgmt page.</h3><h3 data-id="-68"></h3><h3 data-id="2.-select-the-drive-desired-for-the-hot-spare-drive.">2. Select the drive desired for the hot spare drive.</h3><h3 data-id="-69"></h3><h3 data-id="3.-press-f2-and-then-select-make-global-hs.">3. Press F2 and then select Make Global HS.</h3><h3 data-id="-70"></h3><h3 data-id="4.-press-ok.">4. Press OK.</h3><h3 data-id="-71"></h3><h3 data-id="5.-press-esc.">5. Press Esc.</h3><h3 data-id="-72"></h3><h3 data-id="6.-select-ok-to-exit.">6. Select OK to exit.</h3><h3 data-id="-73"></h3><h3 data-id="7.-press-ctrl-%2B-alt-%2B-del-to-reboot-the-system.">7. Press Ctrl + Alt + Del to reboot the system.</h3><h3 data-id="-74"></h3><h3 data-id="-75"></h3><h3 data-id="-76"></h3><h3 data-id="-77"></h3><h3 data-id="-78"></h3><h3 data-id="2.-select-the-raid-level-desired-and-enter.-1">2. Select the RAID Level desired and Enter.</h3><h3 data-id="-79"></h3><h3 data-id="3.-select-select-drives-for-the-virtual-drive-and-apply-the-changes-1">3. Select Select Drives for the virtual drive and apply the changes</h3><h3 data-id="-80"></h3><h3 data-id="4.-specify-the-virtual-drive-size.-1">4. Specify the virtual drive size.</h3><h3 data-id="-81"></h3><h3 data-id="5.-select-save-configuration.-1">5. Select Save Configuration.</h3><h3 data-id="-82"></h3><h3 data-id="6.-check-confirm-and-then-select-yes.-1">6. Check Confirm and then select Yes.</h3><h3 data-id="-83"></h3><h3 data-id="7.-select-ok.-1">7. Select OK.</h3><h3 data-id="-84"></h3><h3 data-id="8.-press-esc-to-return-to-top-menu.-1">8. Press Esc to return to top menu.</h3><h3 data-id="-85"></h3><h3 data-id="initializing-a-raid-volume-(efi-mode)-1">Initializing a RAID Volume (EFI Mode)</h3><h3 data-id="-86"></h3><h3 data-id="1.-select-main-menu-virtual-drive-management-virtual-drive-that-you-just-created.-1">1. Select Main Menu > Virtual Drive Management > Virtual Drive that you just created.</h3><h3 data-id="-87"></h3><h3 data-id="2.-select-operation-by-enter.-1">2. Select Operation by Enter.</h3><h3 data-id="-88"></h3><h3 data-id="3.-select-fast-initialization.-1">3. Select Fast Initialization.</h3><h3 data-id="-89"></h3><h3 data-id="4.-select-go.-2">4. Select Go.</h3><h3 data-id="-90"></h3><h3 data-id="5.-check-confirm-and-then-select-yes.-2">5. Check Confirm and then select Yes.</h3><h3 data-id="-91"></h3><h3 data-id="6.-select-ok.-3">6. Select OK.</h3><h3 data-id="-92"></h3><h3 data-id="7.-press-esc-to-return-to-top-menu.-1">7. Press Esc to return to top menu.</h3><h3 data-id="-93"></h3><h3 data-id="assigning-a-hot-spare-drive-(efi-mode)-1">Assigning a Hot Spare Drive (EFI Mode)</h3><h3 data-id="-94"></h3><h3 data-id="1.-select-main-menu-drive-management-drive-that-you-want-to-assign.-1">1. Select Main Menu > Drive Management > Drive that you want to assign.</h3><h3 data-id="-95"></h3><h3 data-id="1.-select-operation-by-enter">1. Select Operation by Enter</h3><h3 data-id="-96"></h3><h3 data-id="-97"></h3><h3 data-id="-98"></h3><p></p><p><br></p><p> </p> </article> </main>
Videos that might interest you