MY DVI port has stopped Working TC710 . The VGA is still working!

Toody
Toody Member Posts: 5

Tinkerer

IT Is a TC710 with Onboard Video. 
THE DVI was working and it has quit.
I saw a post wich avise reloading the Graphics Driver. 
I cannot find the Driver except I cannot find a Driver online except when they want to use you to Load.
where can I get the newest possible Driver?

Thank You

Best Answer

  • William_mk2
    William_mk2 Ally Posts: 4,084
    Answer ✓
    @Toody

    Sometimes it might also be a cable issue.   Please  try an alternative cable and check..  

    If it still not working..

    Try windows x 
    go to device manager 
    expand display adapter
    right click on display driver - uninstall 
    Restart the computer 

    It should work fine.. 

    If it is still not working 
    Uninstall the display adapter from device manager 
    Dont restart the computer. 
    Go to support.acer.com 
    chose your country 
    type snid or chose your model 
    go to drivers 
    Install the display driver 


    Click on "Like" if you find my answer useful 

    Click on "Yes" if it answers your question.


    Please click YES if I answered your question

    I am not an ACER employee
    B  Thank you and have a BLESSED AND HAPPY DAY  B


                                         ★★ WILLIAM - MRK ★★

Answers

  • billsey
    billsey ACE Posts: 31,672 Trailblazer
    Could you take a picture showing the back of the computer? The service guide shows two HDMI ports and no DVI ports...
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Toody
    Toody Member Posts: 5

    Tinkerer

    My sincere appologies the Motherboard that Quit was the TC710.
    The PC I am replacing it with is a Veritron X498G which has the DVI problem.
    FW ver. P01-B0
    11/25/2010
    Either this version or a newer version!
  • William_mk2
    William_mk2 Ally Posts: 4,084
    Answer ✓
    @Toody

    Sometimes it might also be a cable issue.   Please  try an alternative cable and check..  

    If it still not working..

    Try windows x 
    go to device manager 
    expand display adapter
    right click on display driver - uninstall 
    Restart the computer 

    It should work fine.. 

    If it is still not working 
    Uninstall the display adapter from device manager 
    Dont restart the computer. 
    Go to support.acer.com 
    chose your country 
    type snid or chose your model 
    go to drivers 
    Install the display driver 


    Click on "Like" if you find my answer useful 

    Click on "Yes" if it answers your question.


    Please click YES if I answered your question

    I am not an ACER employee
    B  Thank you and have a BLESSED AND HAPPY DAY  B


                                         ★★ WILLIAM - MRK ★★

  • billsey
    billsey ACE Posts: 31,672 Trailblazer
    P01-B0 is the latest BIOS for the Veriton, so you are good there. The system was initially released with Windows 7 and a downgrade to XP was an option. That puts it age at well over ten years. Acer's support site does have Windows 7 drivers for it and those are the latest. Determine first if you are running 32 bit or 64 bit and download the W7 drivers and try a reinstall. You may have to use compatibility mode to install the W7 drivers if you have W10 on it.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Toody
    Toody Member Posts: 5

    Tinkerer

    I have uninstalled the driver and rebooted to load the driver from the Internet. No Change.
    The DVI did work until I installed the Windows 10.
    I was trying to find the BIOS firmware just to try reloading it!
    However it is not available on the ACER Site that I could find!
  • billsey
    billsey ACE Posts: 31,672 Trailblazer
    Sure, the BIOS is on the Acer site, you likely just need to select the correct OS version, in your case Windows 7 64bit. A typical uninstall of the drivers doesn't actually remove them, there's a checkbox you have to add to remove the files. You don't want Windows to reinstall them, you want to reinstall the version from Acer's support site. Do the uninstall with the checkbox to say remove files. Before rebooting install the ones from the Acer site, in compatibility mode since they are W7 drivers. Then reboot and see it it's made any change.
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.
  • Toody
    Toody Member Posts: 5

    Tinkerer


    I cannot seem to find access to the BIOS and drivers.
    The Acer Care center does not support the Veritron X498G the SN is not listed.
    Is it possible to send me a link to where I can get the Firmware?

    I appreciate the assistance greatly.
  • Toody
    Toody Member Posts: 5

    Tinkerer

    I must apologize!
    I went back and tried the Adapter drivers again.
    I must not have checked the box to remove the software previously.
    I removed the software this time.
    When it rebooted it loaded with the Windows Drivers.
    I updated the Driver and it loaded the Intel driver and works now!

    Thank you very much for your assistance and Patience!

    You have solved another One!
  • billsey
    billsey ACE Posts: 31,672 Trailblazer
    Good job! Glad to see you got it sorted. :)
    Click on "Like" if you find my answer useful or click on "Yes" if it answers your question.